Dyna-Glo Delux RA250NGDGD Bedienerhandbuch PDF herunterladen (Seite 3)

3

E

N

G

L

I

S

H

General Safety Information

(Continued)

– Check heater for damage before each

use. Do not use damaged heater.

Minimum heater clearance from

combustibles:

Sides: 6 feet Top: 5 feet

Floor: Combustible - Not for use

on finished floors

– The heater, other than a heater with

integral propane gas container, must

be located at least 6 feet (in Canada,

distance must be 10 feet) from any

propane gas container.

– Blower or radiant type heaters shall

not be directed toward any propane

gas container within 20 feet (6 m).

– Check hose before each use of heater.

Do not use if hose is cut or damaged.

Replace with hose specified by

manufacturer.

– Always be sure to place the heater on

a stable and level surface while the

heater is in operation.

– The heater is not intended for use

on finished floors. Warping or other

damage may occur.

– Place heater away from any breezes

or drafts. Keep away from dripping

water or rain.

– Keep small children and animals away

from the heater.

– Never handle, move or service a hot or

operating heater. Wait 20 minutes after

turning heater off before touching the

heater. Severe burns can result.

– Always wear gloves when handling

the heater to prevent injury.

– Never attach ductwork to heater.

– Do not alter heater. Keep heater in its

original state.

– Do not use heater if altered.

– Turn off gas supply to heater when

not in use.

– Use only original replacement parts.

This heater must use design specific

parts. Do not substitute or use generic

parts. Improper replacement parts

could cause serious or fatal injury.

Assembly

MODEL RA100NGDGD

1. Provide natural gas supply system.

2. Install plumbing to a low pressure

natural gas source to heater. The

source must be regulated to 1/2 PSI,

maximum 3/4 inch I.D. pipe or flexible

connector, not longer than 10 feet.

3. Be sure to use thread sealing

compound when connecting the hose

to the heater at the 1/2 NPT fitting at

the regulator inlet. Tighten all fittings

with a wrench.

4. Open natural gas supply valve

SLOWLY.

5. Check all connections for leaks.

Never use an open

flame to check for a

leak. Apply 50/50 mixture of liquid soap

and water to all joints. Bubbles forming

show a leak. Correct all leaks at once.

6. Close natural gas supply valve.

MODEL RA250NGDGD

1. Insert AA battery (included)

into ignition by turning

COUNTERCLOCKWISE

and

unscrewing ignition cap.

2. Provide natural gas supply system.

3. Install plumbing to a low pressure

natural gas source to heater.

4. Connect gas supply to heater using

minimum 3/8” ID pipe. Maximum

pipe length is 10 feet.

5. Connect hose or plumbing to 1/2”

NPT flare fitting at the valve inlet.

Tighten all fittings with a wrench.

6. Open natural gas supply valve

SLOWLY. Check all connections for

leaks. Never use an open flame to

check for leaks.

7. Close natural gas supply valve.

NOTE: Keep hands and face away from

outlet (around top of shelf) of heater

while attempting to start heater.

Models RA100NGDGD and RA250NGDGD

Dyna-Glo Delux Operating Instructions and Parts Manual

Figure 2 – Pipe and Valve Inlet

Figure 3 – Heater Control Knob –

RA100NGDGD

PROFESSIONAL GRADE

For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:00 am - 5:00 pm CST www.ghpgroupinc.com

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

1 2 3 4 5 6 7 8 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare